Free tool

Wallpaper Calculator

Find out how many rolls of wallpaper you need for a room. Enter the room and ceiling size, choose your roll size and pattern match, and the calculator counts strips the way a paperhanger does, so the pattern repeat is not forgotten.

Wallpaper calculator

Order (double rolls)

11

Strips (drops)

31

Strips per roll

3

Length of each strip

9.0 ft

The room needs 31 strips, each 108 in long (wall height + 4 in for trimming, rounded up to the pattern repeat). One roll gives 3 strips, so you need 11 double rolls. That is 22 single rolls. For comparison, a plain area estimate (net wall area 365 sq ft plus 15%) suggests only 8 double rolls. The strip count is the safer number. Buy one spare roll from the same batch.

How to work out how many rolls of wallpaper you need

The strip method gives a higher and more honest number than a square foot estimate, because the leftover piece at the end of each roll is usually too short for a full wall. An 8 ft wall plus trim is 100 inches, and a 33 ft roll holds only three of them, so a few inches of every roll go to waste.

One wall, hung in strips20.5 in8 ft6 strips across a 14 ft wallOne 33 ft roll cut into stripsStrip 1Strip 2Strip 3scrapStrip = 8 ft wall + 4 in trim, rounded upto a full 12 in repeat = 108 in
  1. Measure the room perimeter (add all four wall lengths) and the ceiling height, from the baseboard to the ceiling.
  2. Find your roll size on the label or product page. US wallpaper is usually sold as a double roll, about 20.5 inches wide and 33 feet long. Metric rolls are 53 cm wide and 10.05 m long.
  3. Find the pattern repeat on the label: the distance from one point in the design to the same point again. A plain or textured paper has none.
  4. Each strip is as long as the wall height plus about 4 inches to trim at the top and bottom, rounded up to the next full repeat. A half drop pattern needs half a repeat more.
  5. Divide the perimeter by the roll width to get the number of strips. Divide by the strips you can cut from one roll, and round up.

How many strips fit in one roll

This is the number that decides your order. The table shows the strip length and the strips from one US double roll (33 ft, 396 inches) for common ceiling heights and pattern repeats, with a straight match.

Strip length (wall height + 4 in trim, rounded up to the repeat) and strips per 33 ft double roll.
Ceiling heightNo repeat12 in repeat24 in repeat36 in repeat
8 ft100 in, 3 strips108 in, 3 strips120 in, 3 strips108 in, 3 strips
9 ft112 in, 3 strips120 in, 3 strips120 in, 3 strips144 in, 2 strips
10 ft124 in, 3 strips132 in, 3 strips144 in, 2 strips144 in, 2 strips
12 ft148 in, 2 strips156 in, 2 strips168 in, 2 strips180 in, 2 strips

Double rolls needed for common room sizes

These quick answers use 8 ft ceilings and a 20.5 inch wide double roll, with a pattern repeat up to 12 inches. They ignore doors and windows, because strips above and below them still need full-length pieces.

Room perimeterExample roomStripsDouble rolls
40 ft10 x 10 ft248
44 ft10 x 12 ft269
52 ft12 x 14 ft3111
60 ft14 x 16 ft3612
70 ft15 x 20 ft4114
80 ft20 x 20 ft4716

Pattern repeat and match types explained

  • Plain, textured, grasscloth-look and random match papers have no repeat. They waste the least.
  • Straight match: the pattern lines up at the same height on every strip. Each strip is cut to a multiple of the repeat.
  • Half drop (drop match): the pattern on each strip sits half a repeat lower than its neighbor. You lose up to half a repeat per strip, so large half drop patterns need more rolls.
  • A large repeat (24 inches and up) can cost one extra strip per roll. If the result is close to a whole roll, round up.

Always order every roll in one go. Rolls from different print batches can differ slightly in color, and a patch for a future repair needs the same batch.

Wallpaper for an accent wall, ceiling or sloped wall

For one accent wall, divide the wall length by the roll width (20.5 inches on a US roll) and round up to get the strips, then use the strips-per-roll figure in the table for your ceiling height. For a ceiling, count strips across the shorter side and cut each strip as long as the longer side plus 4 inches. For a gable or sloped wall, measure the tallest point of every strip, because that sets the length of the piece you cut.

AI render of a bedroom with pale walls, a sage green bed and oak furniture

See the wallpaper in your room before you buy it

Upload a photo or a plain 3D view of your bedroom or living room and our AI renders it with the wallpaper, paint and finishes you describe, so you can compare options before ordering rolls.

Try the AI interior render

Sign in with Google or email to render. New accounts get 1 free render (watermarked).

Frequently asked questions

How many rolls of wallpaper do I need for a 12 x 14 room?

A 12 x 14 ft room has a 52 ft perimeter. With 8 ft ceilings, a 20.5 inch wide US double roll and a 12 inch pattern repeat, you need 31 strips. Each double roll gives 3 strips, so you need 11 double rolls (22 single rolls). A plain area estimate would say 8, which is why the strip method is safer.

How do I calculate wallpaper rolls with a pattern repeat?

Add about 4 inches to the wall height for trimming, then round that up to the next full pattern repeat to get the length of each strip. Divide the roll length by the strip length and round down to get strips per roll. Divide the strips you need by that number and round up.

Should I subtract doors and windows?

Only a little. Strips above and below a window or door still need full-length pieces, and the cut-offs rarely fit elsewhere. The calculator counts every strip around the room and shows the lower area-based figure for comparison. For a room with several large openings you can sometimes save one roll.

How much extra wallpaper should I buy?

Plan for 10 to 15% extra on plain paper and more for large repeats, which the strip method already covers. Buy one spare roll from the same batch for repairs and for mistakes while hanging.

What size is a standard roll of wallpaper?

In the US a standard double roll is about 20.5 inches wide and 33 feet long, around 56 square feet. In the UK and Europe a standard roll is 53 cm wide and 10.05 m long, about 5.3 square meters. Wide and commercial rolls differ, so use the size on the label.

More free tools for architects and designers

Sources: Strip method, the 4 inch trimming allowance and half drop handling follow common paperhanger practice and retailer guides (Spoonflower, Borastapeter, WallCover). Roll sizes vary by maker: use the size printed on your roll.